Yard Sign Stakes are specifically designed for use with our 4mm corrugated plastic yard signs. These stakes slide into the plastic corrugated flutes of the material. Yard signs must have the flutes oriented vertically for Stakes to work correctly.

H-Wire Stakes are 10″ wide by 30″ high (for a sign that sits 14″ above the ground when Stakes are fully inserted) and constructed from 9 gauge galvanized steel. They will hold a sign stable, though they are recommended for one-time use. The bottom rung of the H-Wire increases stability and may also be used to assist when inserting the stake into the ground.

Beefy Stakes are made from a titanium byproduct, so they are sturdier than H-Wire Stakes. Two beefy stakes are necessary to support a sign, though signs wider than 24″ will likely require 3 stakes, while signs wider than 36″ may require 4.

ART:
Customer must supply appropriately sized print ready art for any images and logos they wish to use on the product. Editing of customer supplied artwork will be at an additional cost.

yard-signs-stakes

Yard Sign Stakes are designed to support our yard signs. They are a helpful tool to ensure your yard signs stay in the locations of your choosing and get seen. Without Yard Sign Stakes, you will need to find another solution to display your yard signs.

Our standard sizes, listed below, are the most popular in the industry:

H-Wire:

    • 10″ wide x 30″ high

 

Beefy Stakes:

    • 26″ tall

 

Pole Wire:

  • 18″ wide x 8″ high

You have options for yard sign stakes.

H-Wire:
Designed to support yard signs 14″ off the ground, these stakes are constructed from 9 gauge galvanized steel. While they will hold a sign stable, they are recommended for one-time use. The bottom rung of the H-Wire increases stability, though it may also be used to assist in inserting the stake into the ground.

Beefy Stakes:
Designed for resilience in wind and to withstand the elements, these stakes are made from a titanium byproduct. Two beefy stakes are necessary to support a sign, though signs wider than 24″ will likely require 3 stakes, while signs wider than 36″ may require 4.

Pole Wire:
Designed to be attached to poles by using plastic ties, these sign holders are a great choice if you would like your sign to be visible at a variety of heights depending on desired use and location.

H-Wire:The steel is untreated and remains a natural gray.

Beefy Stakes:Black titanium.

File Preparation

In order to ensure your files are print-ready, we recommend that you upload them in PDF format. When you generate a print-ready PDF, your computer will use the settings in Adobe Acrobat Distiller or any other PDF generating programs you may use. Please make sure that these are set properly before generating your PDF file.

We also accept .JPG (JPEG), .EPS and .TIF (TIFF) file types, however PDF is the preferred format.

Check your file to make sure it meets our file creation guidelines. This will help speed up the production of your project and give your printed piece the best results.

  1. Use the CMYK colorspace (Cyan, Magenta, Yellow, blacK). These are industry standard printing colors. CMYK colors are different than RGB (Red, Green, Blue), which are used to display colors on your screen.
  2. Use a minimum resolution of 300 dpi for image files.
  3. Specify trim area with crop marks. (Don’t place crop marks inside the work area.)
  4. Artwork should have 1/8″ (0.125″) bleed extending past the trim line. This is to prevent minor cutting variations from leaving unintended results at the trim edge.
  5. Safe Area is the 1/8″ (0.125″) area inside the trim line. Do not put critical information or images within the Safe Area. This is to prevent minor cutting variations from leaving unintended results at the trim edge.
  6. If you want printed borders, they must be placed a minimum of 1/8″ (0.125″) inside the trim line and include bleed. This is to prevent minor cutting variations from leaving unintended results at the trim edge.